Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Toolbox Essentials: Industrial Equipment and Parts [BETA]
Welcome to Toolbox Essentials — Industrial Equipment and Parts
Getting Started
1.0 Introduction to the Curriculum
1.1 Course Welcome
1.2 Course Overview
2.0 Chain Drives
2.1 Introduction to Chain Drives
2.2 Chain Selection and Installation
2.3 Power Train Formulas and Shaft Speed
2.4 Chain Length
2.5 Chain Speed
2.6 Preventive Maintenance Procedures for Chain Drives
2.7 Chain Drive Application (9:46)
2.8 Quiz: Section 2
2.9 Questions?
3.0 Hydraulics
3.1 Introduction to Hydraulics
3.2 Hydraulic Troubleshooter
3.3 Best Hydraulic Repair Practices
3.4 Root Cause Failure Analysis for Hydraulics
3.5 Preventive Maintenance Procedures for Hydraulics
3.6 Measuring Success
3.7 Recommended Maintenance Modifications
3.8 Hydraulic Pumps Application (14:30)
3.9 Quiz: Section 3
3.10 Questions?
4.0 Bearings Part 1
4.1 Introduction to Bearings
4.2 Types of Movements
4.3 Commonly Used Bearing Types
4.3.1 Plain Bearings
4.3.2 Rolling Element or Antifriction
4.3.3 Roller
4.4 Bearing Materials
4.5 Lubrication
4.6 Questions?
5.0 Bearings Part 2
5.1 Installation and General Handling Precautions
5.1.1 Plain Bearing Installation
5.1.2 Roller Bearing Installation
5.1.3 General Roller-Element Bearing Handling Precautions
5.2 Bearing Failures, Deficiencies, and Their Causes
5.2.1 Improper Bearing Selection and/or Installation
5.3 Bearings Application (10:35)
5.4 Quiz: Section 4-5
5.5 Questions?
6.0 Compressors
6.1 Introduction to Compressors
6.2 Compressor Performance
6.3 Centrifugal
6.4 Positive Displacement — Rotary
6.5 Positive Displacement — Reciprocating
6.5.1 Configuration
6.5.2 Performance and Installation
6.6 Troubleshooting
6.6.1 Troubleshooting — Centrifugal
6.6.2 Troubleshooting — Rotary-Type, Positive Displacement
6.6.3 Troubleshooting — Reciprocating, Positive Displacement
6.7 Compressors Application (9:24)
6.8 Quiz: Section 6
6.9 Questions?
7.0 Gears and Gearboxes
7.1 Introduction to Gears and Gearboxes
7.2 Spur Gears
7.3 Pitch Diameter and Center Distance
7.4 Circular Pitch
7.5 Diametrical Pitch and Measurement
7.6 Pitch Calculations
7.7 Tooth Proportions
7.8 Backlash
7.9 Other Gear Types
7.9.1 Bevel and Miter
7.9.2 Helical
7.9.3 Worm
7.9.4 Herringbone
7.9.5 Gear Dynamics and Failure Modes
7.9.6 Common Characteristics
7.10 Troubleshooting
7.11 Gears and Gearboxes Application (10:37)
7.12 Quiz: Section 7
7.13 Questions?
8.0 Electric Motors
8.1 Introduction to Electric Motors
8.2 Electric Motor Parameters
8.3 Electric Motor Analysis
8.4 Electric Motor Application (7:44)
8.5 Quiz: Section 8
8.6 Questions?
Conclusion and Additional Resources
Course Completion
Resources for Further Learning
5.1.2 Roller Bearing Installation
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock